Řazení podle: 
celkem 9 položek

9,-
cena bez DPH 7,44
(id:12-20)
dostupnost: skladem

Hadicová spona šroubovaná se šroubkem SX9 spona na hadice se šroubkem , šroubová hadicová spona profi,pevná hadicová spona se šroubem

Podle šířky pásku je ideální pro spojování hadic v automobilovém průmyslu, v domácnostech, zdravotnictví, ve výrobě a konstrukci strojů a v zemědělství.
Princip šnekového závitu s asymetrickým tělesem zaručuje vysokou těsnící spolehlivost.
- velký upínací rozsah
- stejnosměrné protlačení hadice
- různé šířky pásků
Upínací hlava spony je opatřena kombinovaným šroubem (šestihran s drážkou) takže montáž je jednoduchá a bezproblémová pomocí běžného nářadí: šestihran s klíčem,šroubovák na šrouby.

Standardní provedení spon je z pozinkované oceli. skladem i spony v nerezu.
Size range Width x thickness
8.0 – 160.0 mm* 9.0 x 0.6 mm
16.0 – 160.0 mm* 12.0 x 0.7 mm

10,-
cena bez DPH 8,26
(id:15-17)
dostupnost: skladem

hadicová spona dvououšková 14-17mm,zamačkávací hadicová spona 2x ouško,stiskávací hadicová spona 14-17mm spona Oetier

pozink rozsah 14-17mm
značková origo spona kvalita a notma zaručena

PG 101 Steel, Material no. 1.0338/SAE 1008/1010, zinc-plated
PG 151 Stainless Steel, Material no. 1.4307/UNS S30403
Corrosion resistance according to DIN EN ISO 9227
PG 101 ≥ 96 h
PG 151 ≥ 800 h
Size range
4.1 – 46.0 mm
Some sizes are only available if an appropriate minimum
quantity is ordered.
Oetiker 2-Ear Clamps
The ears of these clamps do not have a dimple and nearly double
the clamping range, compared to the 1-ear clamp. 2 ears provide
a degree of elasticity to accommodate changes in size of the
parts being joined, such as that which may be caused by thermal
expansion or vibration.
Installation techniques are similar to those for 1-Ear Clamps, but
the force applied when closing the second ear may react against
the opposing closed ear and make a second crimping operation
necessary. For perfect sealing, the ears must be adequately
closed during installation.
Assembly recommendations
The ears of these clamps should be closed with the recommended,
uniform force (known as force priority). This method will result in
a constant, reproducible stress within the clamp material, without
overloading either the clamp or the parts being assembled. The
nominal diameter of the clamp should always be chosen so that,
when installed with the correct clamping force, the ears are
almost closed. Complete process monitoring and 100% process
documentation are available using the “Electronically Controlled
Pneumatic Power Tool” Oetiker ELK.
Closing force
The following table shows the maximum applied closing force for
different material dimensions.
Important
Single tool stroke closure only, do not apply secondary
crimping force.
2

10,-
cena bez DPH 8,26
(id:13-15)
dostupnost: skladem

hadicová spona dvououšková 12,5-15mm,zamačkávací hadicová spona 2x ouško,stiskávací hadicová spona 12,5-15mm spona Oetier

pozink
rozsah 12,5-15mm

originální výrobek prvovýroby

PG 101 Steel, Material no. 1.0338/SAE 1008/1010, zinc-plated
PG 151 Stainless Steel, Material no. 1.4307/UNS S30403
Corrosion resistance according to DIN EN ISO 9227
PG 101 ≥ 96 h
PG 151 ≥ 800 h
Size range
4.1 – 46.0 mm
Some sizes are only available if an appropriate minimum
quantity is ordered.
Oetiker 2-Ear Clamps
The ears of these clamps do not have a dimple and nearly double
the clamping range, compared to the 1-ear clamp. 2 ears provide
a degree of elasticity to accommodate changes in size of the
parts being joined, such as that which may be caused by thermal
expansion or vibration.
Installation techniques are similar to those for 1-Ear Clamps, but
the force applied when closing the second ear may react against
the opposing closed ear and make a second crimping operation
necessary. For perfect sealing, the ears must be adequately
closed during installation.
Assembly recommendations
The ears of these clamps should be closed with the recommended,
uniform force (known as force priority). This method will result in
a constant, reproducible stress within the clamp material, without
overloading either the clamp or the parts being assembled. The
nominal diameter of the clamp should always be chosen so that,
when installed with the correct clamping force, the ears are
almost closed. Complete process monitoring and 100% process
documentation are available using the “Electronically Controlled
Pneumatic Power Tool” Oetiker ELK.
Closing force
The following table shows the maximum applied closing force for
different material dimensions.
Important
Single tool stroke closure only, do not apply secondary
crimping force.
2

10,-
cena bez DPH 8,26
(id:11-13)
dostupnost: skladem

hadicová spona dvououšková 10,8-13mm,zamačkávací hadicová spona 2x ouško,stiskávací hadicová spona 10,8-13mm spona Oetier

pozink
rozsah 10,8-13mm
možno i jiné rozměry

PG 101 Steel, Material no. 1.0338/SAE 1008/1010, zinc-plated
PG 151 Stainless Steel, Material no. 1.4307/UNS S30403
Corrosion resistance according to DIN EN ISO 9227
PG 101 ≥ 96 h
PG 151 ≥ 800 h
Size range
4.1 – 46.0 mm
Some sizes are only available if an appropriate minimum
quantity is ordered.
Oetiker 2-Ear Clamps
The ears of these clamps do not have a dimple and nearly double
the clamping range, compared to the 1-ear clamp. 2 ears provide
a degree of elasticity to accommodate changes in size of the
parts being joined, such as that which may be caused by thermal
expansion or vibration.
Installation techniques are similar to those for 1-Ear Clamps, but
the force applied when closing the second ear may react against
the opposing closed ear and make a second crimping operation
necessary. For perfect sealing, the ears must be adequately
closed during installation.
Assembly recommendations
The ears of these clamps should be closed with the recommended,
uniform force (known as force priority). This method will result in
a constant, reproducible stress within the clamp material, without
overloading either the clamp or the parts being assembled. The
nominal diameter of the clamp should always be chosen so that,
when installed with the correct clamping force, the ears are
almost closed. Complete process monitoring and 100% process
documentation are available using the “Electronically Controlled
Pneumatic Power Tool” Oetiker ELK.
Closing force
The following table shows the maximum applied closing force for
different material dimensions.
Important
Single tool stroke closure only, do not apply secondary
crimping force.
2

11,-
cena bez DPH 9,09
(id:E770212)
dostupnost: skladem

Hadicová spona - dvououšková zamačkávací , spona deformační na hadici, zamačkávací spona na hadice

K dodání v různých materiálech a provedních

Spona deformační na hadici pr. 15-17mm, SLK 15-17mm

Charakteristika :
- ocelové provedení, leskle pozinkované s 2 profilovými uchy
- šířka pásku 7 mm
- pro hadice

11,-
cena bez DPH 9,09
(id:16-19)
dostupnost: skladem

hadicová spona dvououšková 16-19mm,zamačkávací hadicová spona 2x ouško,stiskávací hadicová spona 16-19mm spona Oetiker

pozink
značkový výrobek

rozsah 16-19mm
PG 101 Steel, Material no. 1.0338/SAE 1008/1010, zinc-plated
možno i nerez
Corrosion resistance according to DIN EN ISO 9227
PG 101 ≥ 96 h
PG 151 ≥ 800 h
Size range
4.1 – 46.0 mm
Some sizes are only available if an appropriate minimum
quantity is ordered.
Oetiker 2-Ear Clamps
The ears of these clamps do not have a dimple and nearly double
the clamping range, compared to the 1-ear clamp. 2 ears provide
a degree of elasticity to accommodate changes in size of the
parts being joined, such as that which may be caused by thermal
expansion or vibration.
Installation techniques are similar to those for 1-Ear Clamps, but
the force applied when closing the second ear may react against
the opposing closed ear and make a second crimping operation
necessary. For perfect sealing, the ears must be adequately
closed during installation.
Assembly recommendations
The ears of these clamps should be closed with the recommended,
uniform force (known as force priority). This method will result in
a constant, reproducible stress within the clamp material, without
overloading either the clamp or the parts being assembled. The
nominal diameter of the clamp should always be chosen so that,
when installed with the correct clamping force, the ears are
almost closed. Complete process monitoring and 100% process
documentation are available using the “Electronically Controlled
Pneumatic Power Tool” Oetiker ELK.
Closing force
The following table shows the maximum applied closing force for
different material dimensions.
Important
Single tool stroke closure only, do not apply secondary
crimping force.
2

11,-
cena bez DPH 9,09
(id:17-20)
dostupnost: skladem

hadicová spona dvououšková 16,2-20mm,zamačkávací hadicová spona 2x ouško,stiskávací hadicová spona 16,2-20mm spona Oetiker

pozink
rozsah 16,2-20mm

PG 101 Steel, Material no. 1.0338/SAE 1008/1010, zinc-plated
PG 151 Stainless Steel, Material no. 1.4307/UNS S30403
Corrosion resistance according to DIN EN ISO 9227
PG 101 ≥ 96 h
PG 151 ≥ 800 h
Size range
4.1 – 46.0 mm
Some sizes are only available if an appropriate minimum
quantity is ordered.
Oetiker 2-Ear Clamps
The ears of these clamps do not have a dimple and nearly double
the clamping range, compared to the 1-ear clamp. 2 ears provide
a degree of elasticity to accommodate changes in size of the
parts being joined, such as that which may be caused by thermal
expansion or vibration.
Installation techniques are similar to those for 1-Ear Clamps, but
the force applied when closing the second ear may react against
the opposing closed ear and make a second crimping operation
necessary. For perfect sealing, the ears must be adequately
closed during installation.
Assembly recommendations
The ears of these clamps should be closed with the recommended,
uniform force (known as force priority). This method will result in
a constant, reproducible stress within the clamp material, without
overloading either the clamp or the parts being assembled. The
nominal diameter of the clamp should always be chosen so that,
when installed with the correct clamping force, the ears are
almost closed. Complete process monitoring and 100% process
documentation are available using the “Electronically Controlled
Pneumatic Power Tool” Oetiker ELK.
Closing force
The following table shows the maximum applied closing force for
different material dimensions.
Important
Single tool stroke closure only, do not apply secondary
crimping force.
2

15,-
cena bez DPH 12,40
(id:11-13r)
dostupnost: skladem

hadicová spona jednooušková 11-13mm,zamačkávací hadicová spona s vnitřním ochranným kroužkem 1xouško,stiskávací hadicová spona 11-13mmmm spona Oetiker s vnitřní ochranou hadice

rozsah 11-13mm
pozink
je možno i jiné rozsahy a nerez

17,-
cena bez DPH 14,05
(id:11,3rer)
dostupnost: skladem

hadicová spona jednooušková nerez 9,1-10,8mm,zamačkávací hadicová spona s vnitřním ochranným kroužkem 1xouško,stiskávací hadicová spona 9,1-10,8mm spona Oetiker s vnitřní ochranou hadice

materiál nerez
rozsah 9,1-10,8mm
možno i jiné velikosti a materiál i pozink

TOPlist